• Single belt head machines
• Light duty, intermittent operation
• For jobbing shops or work cells
• 225 and 600mm working widths, dry
• 225mm working width wet
• Variable throughfeed speed
• Powered table set, digital readout and load meter on 600mm
• Scratch grain finishes with abrasive belt
• Satin grain finish with nylon web belts
• 127mm (on 225mm) and 205mm (on 600mm) minimum component length
• Dryer and filter on wet machines

• Magnetic table
• Different hardness contact rollers

• Second abrasive belt head

• For deburring punched, nibbled, sheared or laser-cut sheet metal parts.
• For calibrating or keying carbon, rubber, wood or other soft materials.
• For grain finishing any material.
• Centralised operator control panel.
• 900, 1100mm, 1350mm working widths
• Wide belt head with fine adjustments of contact roll, 150mm.
• Two speed main motor
• Conveyor bed on 4 heavy duty precision spindles, each 2 tons capacity.
• Ridged, precision made, rubber coated, workpiece hold down rolls.
• Motorised, single point thickness setting.
• Electronic digital thickness read-out.
• Frequency controlled feed motor with conveyor reverse for set-up.
• Dust extraction funnel(s).
• Enclosed heads and motors for minimising noise levels.
• Hour counter

• Brush head with fine adjustment (Brush 200mm) and brush oscillation.
• Steel wire, Stainless wire, Nylon web, Slashed abrasive brushes
• Extended opening to 300mm

• Belt only
• Belt + belt
• Belt + brush
• Brush + belt
• Belt + belt + brush
• Belt + belt + brush (slaggrinding specification)
• Belt + brush + brush

• For deburring punched, nibbled, sheared or laser-cut sheet metal parts.
• For calibrating or keying carbon, rubber, wood or other soft materials.
• For grain finishing any material.
• Centralised operator control panel.
• 600, 900, 1100, 1350mm working widths
• Wide belt head with fine adjustments of contact roll, 180mm.
• Conveyor bed on 4 heavy duty precision spindles, each 2 tons capacity.
• Ridged, precision made, rubber coated, workpiece hold down rolls.
• Motorised, single point thickness setting.
• Electronic digital thickness read-out.
• Frequency controlled feed motor with conveyor reverse for set-up.

• Orbital action abrasive pads
• Brush head with fine adjustment (Brush 200mm) with fast brush oscillation:
  • Steel wire brush (60 strokes/min.)
  • Nylon web brush (60 or 120 strokes/min)
  • Quick exchange brush slide complete with shaft and bearings.
• Two speed or Variable speed grinding motors.
• Fixed/floating conveyor table
• Constant pass line.
• Component cleaning brush.
• Reverse feed cycles with retractable heads.
• Stand-alone (in lieu of standard) parts dryer for wet-working machinery.
• Extended opening to 250mm.
• Vacuum table.

• Dust extraction funnel(s)
• Motors enclosed within machine frame

• Automatic coolant filtration system.
• Integral parts dryer (minimum component length 80mm).
• 3 sets of squeeze rolls.
• 2 sets of air knives.
• Noise insulated blower.
• Non-stainless machine components treated with rust preventative coatings.
• Quick exchange spray nozzle pipes for ease of maintenance.
• Centralised lubrication for high speed bearings.
• Each brush head includes a stainless steel wire brush, optionally, nylon web.

• 600mm & 900mm operating widths
• Main motor brakes
• Stainless Steel construction for:
• Wet operation with:
  • Built-in filtration plant
  • Built-in air knife dryer
• Constant Pass line
• Electronic Abrasive belt tracking
• Variable throughfeed speed (4.5-14m/min)
• Conveyor belt tracking
• Colour graphic control interface (HMI)
• Automatic lubrication to high speed bearings
• Digital thickness readout and
• Powered table set

• Built-in Brush head with
  • Brush Oscillation

• For deburring punched, nibbled, routered, laser-cut or sheared, sheet metal parts (with or without cladding removal).
• For calibrating or keying aluminium castings and other soft materials.
• For cleaning and grain finishing any material.
• For plasma and slag removal
• Available in 600, 900, 1100 and 1350mm working widths
• 1 to 5 Abrasive Belt, Brush and/or Disc heads.
• Wet or dry

Additional Specification for Precision Applications:

• Specific Surface Finish Generation, grained, brushed, sueded, smoothed.
• Accurate thickness Calibration
• Contact rollers / Brushes / Nylon Web discs / Orbital action abrasive pads / Platen heads as required.
• Hydraulically driven throughfeed conveyor
• Multiple, hard, compact, high speed rollers for stock removal
• 1 or 2 Large diameter brushes for edge deburring

• For deburring punched, nibbled, routered, laser-cut or sheared, sheet metal parts (with or without cladding removal).
• For calibrating or keying aluminium castings and other soft materials.
• For cleaning and grain finishing any material.
• For plasma and slag removal
• Available in 600, 900, 1100 and 1350mm working widths
• 1 to 5 Abrasive Belt, Brush and/or Disc heads.
• Wet or dry

• Aerospace Alclad deburring, without removing the cladding.
• Electromotive Punched, Lacquered Steel deburring, bottom working, without removing the coating.
• Fine Blanked component deburring without grinding.
• Patented, inagressive abrasive belt heads for removing excess vertical, punch or router burr with
• Abrasive belt air cushioning.
• Ajustable low contact pressure, low running speed (&/or)
• Special purpose nylon web brushes for quick radiusing (&/or)
• High speed rotating nylon web discs for controlled radiusing
• Very high throughfeed speeds for punched laminations (30-45m/min)
• And (as applicable)
  • Vacuum table for small parts
  • Wet working operation with built in filter and dryer
  • Bottom working

• For deburring punched, nibbled, routered, laser-cut or sheared, sheet metal parts (with or without cladding removal).
• For calibrating or keying aluminium castings and other soft materials.
• For cleaning and grain finishing any material.
• For plasma and slag removal
• Available in 600, 900, 1100 and 1350mm working widths
• 1 to 5 Abrasive Belt, Brush, Disc or Orbital brush heads.
• Wet or dry

• (Drill Burr, Oxy-, Plasma and Laser Slag Removal)
  • Pneumatic floating bed for distorted work
  • Hard, compact, high speed #1 head for slag removal
  • Flexible, sensitive, diamond pattern #2 head for contour following
  • 1 or 2 Large diameter brushes for edge dulling and derusting
  • Rotating orbital slashed abrasve brushes for generating radiusses
• (Oxide Removal)
  • Hard, compact, high speed #1 head for skin removal (&/or)
  • Medium, grooved, #2 head for standard grain finish (&/or)
  • Soft #3 head for fine finishes (&/or)
  • 1 or 2 Large diameter brushes for soft brushed finishes

• For deburring punched, blanked, nibbled, routered, laser-cut or sheared sheet metal parts (with or without cladding removal)
• For calibrating or keying aluminium castings and other soft materials.
• For cleaning and grain finishing any material.
• For plasma and slag removal
• Available in 600, 900, 1100 and 1350mm working widths
• 1 to 5 Abrasive Belt, Brush and/or Disc heads.

• Centralised operator control panel.
• Wide belt head with fine adjustments of contact roll, 180mm or  280mm.
• Brush head with fine adjustment (Brush 280mm).
• Fast brush oscillation.
  • Steel wire brush (80 strokes/min.)
  • Nylon web brush (60 or 120 strokes/min)
• Quick exchange brush slide complete with shaft and bearings.
• Conveyor bed on 4 heavy duty precision spindles, each 2 tons capacity.
• Ridged, precision made, rubber coated, workpiece hold down rolls.
• Motorised, single point thickness setting.
• Electronic digital thickness read-out.
• Frequency controlled feed motor with conveyor reverse for set-up.

• Pre-programmable execution settings for part thickness, abrasive belt head depth and brush or disc head depth.
• Multiple reciprocating cycles with pre-programmable stock removal and number of cycles
• Fixed/floating conveyor table
• Constant pass line.
• Component cleaning brush.
• Reverse feed cycles with retractable heads.
• Stand-alone parts dryer for wet-working machinery.
• Heavier / Multiple speed / Variable speed main motors.
• Magnetic / Vacuum conveyor table
• Digital feed speed readout

• Dust extraction funnel(s).
• Motors enclosed within machine frame

• Automatic coolant filtration system.
• Integral parts dryer (minimum length 80mm).
  • 3 sets of squeeze rolls.
  • 2 sets of air knives.
  • Noise insulated blower.
• Non-stainless machine components treated with rust preventative coatings.
• Quick exchange spray nozzle pipes for ease of maintenance.
• Centralised lubrication for high-speed bearings.
• Each brush head includes a stainless steel wire brush, optionally, nylon web.

• Available in 1350, 1600, 2150 and 2400mm working widths
• Single or Multiple abrasive belt heads.
• Wet or Dry Optional
• For grain and brush finishing of sheet, plate and coil
• For high accuracy calibrating or large area keying of rubber, plastics, cork and other soft materials.
• Centralised PLC driven Control Panel
• Powered, Remote adjustments of heads
• Worm and Gearbox driven Roller Table
• Case Hardened Steel Billy-Rollers
• Remotely monitored and Self-levelling Billy-Roller
• Solid Core Grinding Aggregates
• In-machine Grinding Roller dresser
• High dynamic balance for chatter-free finishing
• Very high precision and tolerance grinding
• Tailored to suite your requirements
• Fully integrated lines
• Full integration into your existing line

• Available in 900, 1350, 1600 and 2150mm working widths
• Single or Multiple Abrasive Belt or Brush heads.
• Wet or Dry Optional
• Centralised operator control panel.
• Wide belt head with fine adjustments of contact roll, 280 & 180mm.
• Brush head with fine adjustment (Brush 200mm).
• Brushing Machines with Very High Oscillation Rates (700 strokes/min)
• Quick exchange brush slide complete with shaft and bearings.
• Conveyor bed on 4 heavy duty precision spindles, each 2 tons capacity.
• Ridged, precision made, rubber coated, workpiece hold down rolls.
• Motorised, single point thickness setting.
• Electronic digital thickness read-out.
• Frequency controlled feed motor with conveyor reverse for set-up.

• Pre-programmable execution settings for part thickness, abrasive belt head depth and brush head depth.
• Multiple reciprocating cycles with pre-programmable stock removal and number of cycles
• Fixed/floating conveyor table
• Constant pass line.
• Component cleaning brush.
• Reverse feed cycles with retractable heads.
• Stand-alone parts dryer for wet-working machinery.
• Heavier main motors.
• Variable speed main motors
• Magnetic conveyor table
• Vacuum conveyor table
• Digital feed speed readout

• Dust extraction funnel(s).
• Enclosed heads and motors for minimising noise levels.

• Automatic coolant filtration system.
• Integral parts dryer
  • 3 sets of squeeze rolls.
  • 2 sets of air knives.
  • Noise insulated blower.
• Non-stainless machine components treated with rust preventative coatings.
• Quick exchange spray nozzle pipes for ease of maintenance.
• Centralised lubrication for high speed bearings.
• Each brush head includes a stainless steelwire brush, optionally, nylon web.

• Reciprocating Table Bed Sizes available to custom sizes
• Vacuum and/or Magnetic Clamping
• Single or Multiple abrasive belt heads
• Automatic Control of all parameters
• Creep feed for high stock removal
• Close tolerance thickness and flatness
• Low Ra finishing
• Machining mark free finish
• Quick change abrasive belt
• Wet operation
• High Volume flood coolant
• Stand-alone High-throughput filtration
• Drag conveyor and paper filter bed

• Specialist tank working machines for:
• internal and external seam weld dressing
• internal and external tank barrel processing
• internal and external dished end finishing
• Can be configured to take any size
• Utilises abrasive belts, flap wheels, brushes and mops

• 4-axis CNC
• For dished ends 3000, 4000, 5000 or 6000mm Ø Options
• For large “rectangular” components
• Linish, brush and/or polish on one set-up
• Automatic speed compensations for position and consumable Ø
• Floating, constant pressure consumables
• Interpolated and integral movement of all axes

• Automatic consumable changer
• Second consumable head
• Two consumables per head
• Bespoke size

• For automatic internal and external finishing of tubular tank bodies
• 0-5000mm plunge
• 3000, 4000, 5000 and 6000mm Ø Options
• For semi-automatic finishing of tank ends
• 3-axis PLC

• Tank body / tank end handling and fixturing
• 4th axis
• CNC

• For manipulating 1 to 4 consumables
• Can process 1 to 4 components simultaneously
• Takes abrasive belts, flap wheels, brushes and mops
• Programmable consumable and component manipulation
• 2-axis consumable movement
• 3-axis component movement
• Full axis interpolation and integration
• Automatic speed and diameter compensation for consumable wear
• Interpolated traverse speed 0-15m/min
• Standard axes 1300mm(X), 850mm(Y), 850mm(Z)
• PC and PLC interfaces

• Constant pressure control
• 4th component axis
• One to four consumables per head
• Automatic consumable changer
• One, two or four workspindles (simultaneous operation)
• Automatic component handling
• Extended axes
• Bespoke clamping
• Enclosure

• Programmable robotic manipulative arm(s)
• 6-axes of movement
• Full axis interpolation and integration
• Working radius 1360mm
• Positioning repeatability 0.03mm
• Maximum straight line speed 1.5m/min
• Maximum swing speed 13.0m/min
• Teach-in or Keyboard programming
• Integrated PC and PLC
• External PC and PLC interfaces
• Cycle integration with external belt and wheel units
• Automatic wear compensation
• For manipulating components of up to 200Kg
• Utilises a cell of consumables
• Takes abrasive belts, grinding wheels, flap wheels, brushes and mops

• Bespoke configurations
• High capacity magazines for unattended extended runs
• Integration into process lines
• Bespoke component clamping
• Enclosure

• For high gloss and longitudinal brush finishing of round tube and bar
• Reciprocating fixture
• Opposing mop and brush sets
• One or two mop sets
• 10 – 100mm Ø x 6000mm (max)
• 4 to 8 workpiece spindles

• From 250-500mm wide x 500-2000mm long
• For high gloss and brush finishing of flat surfaces
• Reciprocating table
• Single or multiple head variants
• Machine mounted heads
• Pressure control
• Buff wear compensation
• Automatic sequencing of heads on multi-head operations
• Plc for programming and storing different processes
• Positionable pendant control panel

• Bespoke table sizes
• Buff oscillation
• Heavy duty, floor mounted heads
• Tailstocks for round tubes / bars
• Automatic liquid compound application

• From 700 – 1500mm wide x 2000 – 7000mm long
• For high gloss and brush finishing of flat surfaces
• Reciprocating table
• Single or multiple head variants
• Double column overhung heads
• Automatic pressure control
• Electronic wear compensation
• Automatic sequencing of heads on multi-head operations
• Plc for programming and storing different processes
• Positionable pendant control panel

• Bespoke table sizes
• Integration with handling equipment
• Buff oscillation
• Constant surface speed control
• Automatic liquid compound application
• Mechanical or vacuum clamping

• For high gloss, brush and scratch finishing of hollow-ware
• External surface finishing
• Rotary transfer system
• Multiple heads
• PLC or CNC cycle control
• Single mainframe machine
• Index rotation (RSB) with:
• Programmable acceleration and deceleration characteristics or:
• Multispindle continuous rotation (RMSB)
• 2-10 polishing, brushing or graining heads
• PLC or CNC control of the cycle
• Centralised operator control
• Variable workspindle speed

• Automatic pressure and wear compensation of consumable
• Vacuum, collet or tailstock fixturing
• PLC or CNC heads
• Machine enclosure
• Comprehensive, powered head setting

• For high gloss, brush and scratch finishing of hollow-ware
• Internal and external surface finishing
• Rotary transfer system
• Continuous or indexing operation
• Multiple heads
• Modular, free standing construction
• Horizontal, vertical or derived consumable paths
• Programmable acceleration and declaration characteristics
• 4-10 table spindles
• Driven abrasive belt, passive abrasive band, gloss mop, nylon web pad and brush heads available
• Internal or external operation
• Centralised or dispersed controls

• Automatic pressure and wear compensation of consumables
• Vacuum, collet or tailstock fixturing
• Automatic handling
• Integration into production lines
• Machine enclosure
• Comprehensive, powered head setting
• PLC or CNC cycle control

• Throughfeed machines
• Scratch or satin brushing
• Two faces simultaneously
• For long Aluminium extrusions or similar
• Heavy duty throughfeed machine
• 250mm x 200mm (w x h – max)
• Variable throughfeed speed
• 3 or 4 opposing brush sets
• Variable brush rotation speed
• Constant passline
• Wet or dry variants
• Can accommodate Wire, nylon filament, nylon web and abrasive flap cylinder brushes

• Infeed/Outfeed tables

• Heavy duty throughfeed machine
• 150, 200 and 250mm working widths
• For fixtured and non-fixtured work
• For grain, scratch, brush or satin finishes
• For deburring pressed, punched and lasered parts
• Wet or dry variants
• 1 – 8 heads
• Abrasive belt, abrasive brush or wire brush heads
• Contact rollers, platens, pads, rotary, cylinder, disc or planetary brushing
• Variable throughfeed speed
• Constant passline

• Return conveyor to return parts to loading area
• Return conveyor for continuous fixtures
• Return handling system for very long parts
• Infeed/outfeed tables
• Magnetic table and de-gaussing tunnel

• Throughfeed, centreless action machines
• For round, ovaloid or tapered tube, bar and rod
• Floating supports for distorted or shaped components
• 6-125mm Ø (CT) and 20-250mm Ø (CT(P))
• Wet and/or dry variants
• Abrasive belt, abrasive flap, nylon web, nylon filament or wire brushes,mops and abrasive wheels
• For grinding, graining, brushing, satinising and gloss polishing
• 1-3 head modules

• Heavy duty free-standing infeed/outfeed tables
• Integration of multiple modules
• Automatic set-up (CT(A)) by PLC or CNC
• Infeed/outfeed magazines and part handling
• Enclosures
• Remote control

• Batch operation
• Pre-set fixtures
• Cam control
• For Grain finishing, area specific grinding, scratch or satin brushing and mop glossing
• External contours
• External and internal finishes

• Greater axis travel
• PLC integrated ‘Z’ axis movement

• Cam operated pneumatically floating turntable
• Abrasive or Nylon Web belts, Nylon Filament or Web, Wire or Abrasive Flap Brushes
• For weld dressing, shape generation or area specific finishing
• 0 – 45 consumable angle
• Adjustable consumable height
• Max. part envelope 400mm

• Batch operation
• Pre-set fixtures
• Cam control
• For Grain finishing, area specific grinding, scratch or satin brushing and mop glossing
• External contours
• External and internal finishes

• Cam follower for irregularly shaped parts
• Cam controlled workspindle rotation for interrupted rotation and reverse
• Vacuum, pneumatic and mechanical fixturing

• Workholding manipulator used in conjunction with polishing lathe (Autopulit PF-II)
• For graining, scratching, satinising or polishing external faces of round parts
• For “side-on” or “end-on” work
• Variable rotation speed
• Variable processing time
• Variable processing pressure
• Adjustable stroke and speed of oscillation
• 6-axis component positioning adjustment
• Three consumable speeds (on PF-II)
• Manual override

• Batch operation
• Pre-set fixtures
• Cam control
• For Grain finishing, area specific grinding, scratch or satin brushing and mop glossing
• External contours
• External and internal finishes
• For graining, scratching, satinising or gloss polishing
• Inside or Outside holloware
• Single or Double spindle variants
• Part by part loading and operation
• Spinning part / Fixed consumable
• Two speed main motor 1500/3000 rpm
• Workholding by vacuum chuck
• Consumable plunge, drop and pull actions
• Consumable float
• PLC process control
• Hydraulic drive for consumable actions

• For vertical graining of hinge knuckles
• Floating contact pad for distorted barrels
• Reciprocating cycle, one component per pass
• Part rotation automatically linked to stroke position
• Variable speed
• PLC

• For ‘swirl’ finishing of sheet
• Three pneumatically pressurised tool sets
• Reciprocating table, encoder governed
• 1000, 1250 or 1500mm x 2000 or 4000mm table size
• Patterning stones 30-60mm Ø
• Tool group width 250-500mm
• Process speed 0-10m/min
• CNC

• 5, 7.5 & 10hp twin main motors available
• Three speed options 1500 / 2000 / 3000rpm
• Up to 150mm face width on consumables
• Up to 400mm Ø mop / brush capacity
• Mop / brush / backstand options
• Various roller hardness’s available

• Combined spindle drive
• Single main motor 5, 9 & 12hp available
• Twin main speed 1500 / 3000 rpm
• Up to 100mm face width on consumables
• Up to 200mm Ø mop / brush capacity
• Mop / brush / backstand options
• Various roller hardness’s available

• Throughfeed grinding
• Wet working
• Stainless Steel construction
• 200 & 300mm operating widths
• Up to 4 Abrasive belt heads
• Coated abrasives and/or nylon web belts
• Two speed conveyor 5 and 10m/min
• Integral coolant recirculation pump
• Integral automatic papre gravity filter
• Outfeed blower / dryer

• Magnetic table
• Variable speed conveyor
• Electrical control of primary functions
• Electronic display of machine functions
• Conveyor cleaning brushes
• Pneumatic abrasive belt tensioning
• Pneumatic belt tracking

• Throughfeed grinding and/or cylinder brushing
• Oscillating cup brush heads
• 300 & 650mm operating width
• Up to 6 heads in any combination of belts and/or cylinder/cup brushes
• Two speed conveyor 5 and 10m/min

• Magnetic table
• Variable speed conveyor
• Electrical control of primary functions
• Electronic display of machine functions
• Conveyor cleaning brushes
• Pneumatic abrasive belt tensioning
• Pneumatic belt tracking

• Throughfeed grinding and brushing machines
• Top and/or bottom working
• 200, 300 and 650mm working widths
• Roller, Platen or Brush heads
• Up to 6 heads in any combination of belts and/or brushes
• Wet or dry formats
• Two speed conveyor 5 & 10 m/min
• Belt oscillation (optional on 200mm)

• Magnetic table
• Variable speed conveyor (3-15 m/min)
• Electrical control of primary functions
• Electronic display of machine functions
• Conveyor cleaning brushes
• Pneumatic belt tensioning
• Pneumatic belt tracking

• Throughfeed Graining / Deburring / Brushing Machine
• 150mm & 200mm Working Widths
• Roller or Brush Heads
• Up to 4 heads in various combinations
• Two Speed Conveyor 5&10 m/min
• Fixed table height/adjustable head height

• Magnetic table
• Variable speed conveyor (3-15 m/min)
• Wet operation with Stainless steel cladding and paper filter
• Electrical control of primary functions
• Electronic display of machine settings
• Pneumatic belt tension
• Pneumatic belt oscillation
• Pneumatic floating heads

• Abrasive Belt Aggregate:
• Auto-Motor Start / Stop
• 3kW – 20m/s
• 75 x 1900mm Abrasive Belt
• Polishing / Brushing Aggregate:
• Auto-Motor Start / Stop
• 4kW
• Mop / Brush Variation 300-180mm Ø
• Adjustable attack angle 0-15°
• Variable Height main Table:
• 0-600mm Opening
• 850 x 2500mm Table Area

• Motorised Table Height Adjustment
• Larger Table 850 x 3420mm
• 3rd Head
• Different Combinations of Abrasive belt & Mop / Brush Heads

• 200, 300 and 650mm Working Widths
• 3,4 and 7.5 kW Main Motor
• Tiltable Table 0 – 45°
• Abrasive Belt Oscillation and Automatic Tracking

• Tiltable worktable
• Wheel end tables
• 100 or 120 and 250mm Ø wheels
• 4 HP main motor
• 200 x 3200mm abrasive belt
• Tiltable belt aggregate

• Rubber coated wheels
• Bespoke machine, wheel and table sizes
• Abrasive belt oscillation

• 850 x 2500mm table
• 5.5 HP main motor
• 150 x 7150mm abrasive belt
• 0-600mm opening

• Powered table raise & lower
• Bespoke machine and table sizes
• Variable speed grinding belt

• 850-1300 (300-1500) rpm, 1.5 (2.2-3) Kw main motor
• 2 x 30 (35) Ø x 200mm mandrels
• To take 350 Ø x 100 or 200mm brush or
• Pneumatic drum, sizes 60, 76, 101, 152 or 203 Ø 200mm
• Or Abrasive belt
• Or Abrasive disc

• Spindle pitch -10° to +45°
• 1500rpm, 1.5Kw main motor
• 30 or 50 Ø x 200mm mandrel
• 1000 x 600mm table

• To take 5’’, 8’’ or 12’’ Ø mops
• Polishing guards
• 1400, 2800 or 1400/2800 rpm motor
• Circuit breaker main switch
• Tapered spindles (on 5’’)

• To take 8’’ or 12’’ Ø wheels
• Adjustable eye-shields
• Heavy cast iron tool rest
• Circuit breaker main switch
• Prepared for connection to external extraction
• 1400 or 2800 rpm motor

• 75 and 150mm working widths
• 4.8 hp motor
• Adjustable from below horizontal to vertical
• Adjustable eye-shield
• Adjustable tool rest
• Circuit breaker main switch
• Prepared for connection to external extraction
• Spark arrester

• Built-in dust bag collection system
• Cyclone extraction
• Direction reverse switch
• Brake motor
• 2 speed motor
• Higher powered motor
• Choice of contact wheel hardness

• 50, 75, 100 and 150mm working widths
• 3.6, 4.1, 4.8, 5.5hp 3 phase
• Plateau and contact wheel grinding areas
• Adjustable pitch
• Adjustable eye-shield
• Adjustable tool rest
• Circuit breaker main switch
• Prepared for connection to external extraction
• Spark arrester

• Built in dust bag collection system
• Cyclone extraction
• Brake motor
• 2 speed motor
• Higher powered motor
• Choice of contact wheel hardness